Bipods Etc

 

Up
Fulcrum Extender

 

Fulcrum extender Operating instructions are here

Special Offer,  Fulcrum Extender KIT 280.00 Just add rifle.

The kit represents a 15.00 saving over items bough separately.

I shoot with one of these at ranges up to 1000 meters or 1KM and found a real difference in accuracy over a standard bipod. Even at 100 yards there is a noticeable difference. Wish I had one years ago.

 

 

 

 

 

 

 

 

 

 

 

 

The Kit is every thing you need except the rifle and comprises of

A Fulcrum extender model B with upgraded handles.

 Firewolf long range Bipod.

13 slot Picatinny rail plus 3 levelling wedges  to ensure the  Picatinny rail is parallel with the barrel. (screws or bolts are not supplied)

Bipod Fulcrum Extender.

 

 

 

 

 

 

 

 

 

 

The Fulcrum Extender is designed to allow you to move your bipod forward to the end of your barrel thus moving the fulcrum.  When shooting accurately you want the  end of the barrel pointing at the target with as little movement as possible, if you look at a seesaw you will notice the two ends go up and down but the pivot point (fulcrum) stays at the same height and moves very little. With a bipod attached to your rifle in the usual position the stock is at one end of the seesaw with the barrel at the other end, both rotate around the bipod. By moving the bipod to the end of the barrel the  rifle is only one end of the seesaw with the end of the barrel at the pivot point. Movement is greatly reduced.

As the rifle is now supported at the ends only all the weight of the rifle is  keeping the rifle stable and reducing felt recoil and muzzle jump. This unit has been successfully tested on 338 Lapua magnum.

 

 Please note the tube clamp must be very tight especially on high recoiling rifles, Failure to keep this clamp tight will result in the tubes  sliding apart and possibly scratching the finish. This is not covered under warranty

 

Due to the way you attach the bipod to this device you only gain approximately 1/2 inch 12/14mm underneath the rifle so you can use the same bipod as you are already using.

Requires a 13 slot Picatinny rail on the bottom of your rifle for the fulcrum extender to attach too. (see below)

13 slot Picatinny rail can be supplied at the same time for 10.00 for you to fit to your rifle. (screws or bolts are not supplied)

 

Several different models are available depending on how you want to attach it to your rifle, from quick release levers, or threaded lever clamps ,see pictures below.

It is possible to have the front end of model A and the rear end of model B  for example, however there is an additional cost for this service. contact me for a quote.

Different Bipod adaptors  are available depending how your bipod attaches . Please state how your bipod attaches to your rifle so the correct adaptor can be supplied.

One adaptor is supplied as standard although not shown in pictures below.

Additional adaptors are available at 15.00 each.

Operating instructions are here

 

Model A

199.00

Can be fitted with quick detach clamps at the front at no extra cost

This model can be fitted with with clamping handles  to match the front end however the one piece mount has to be convert it from quick detach throw leavers to clamping levers  which adds an extra 15.00 including parts. Knobs such as the front of model B for 5.00 less

 

 

 

 

Model B

195.00

This  one is best if you are going to use it on several rifles as Picatinny rails do vary in width very slightly. Clamping levers can replace the knobs on the front end for an extra 5.00, or knobs can be put on the back end for 5.00 less

 

 

 

Model C

189.00

 

 

 

 

 

13 slot Picatinny rail

 

13 slot Picatinny rail  10.00  (screws or bolts are not supplied)

Attach to the bottom of your stock with bolts or screws if the bottom of your stock is parallel with the barrel

 

13 slot Picatinny rail  plus Levelling wedge Kit

13 slot Picatinny rail plus 3 levelling wedges 15.00  (screws or bolts are not supplied)

If the bottom of your stock is not parallel with the barrel the levelling wedges can be used to correct this.

The levelling wedge kit consists of one 13 slot picatinny rail, one 2.5mm high wedge, one 5mm high wedge and one 10mm high wedge, the wedges can also be combined to make 7.5mm, 12.5mm, 15mm and 17.5mm, Additional wedge packs are available at 5.00 per pack. The wedges are solid plastic (PetG) and could be drilled with additional holes for different rails but are designed to fit the 13 slot picatinny rails supplied by reloading.org.uk. They are 137mm x 16mm x various heights and have 3 x 5mm holes.

 

 

 

 

 

Harris Type Bipods

All bipods in this section look like the pictures below.

The  Bipod in the picture is shown with an optional adaptor for attaching to a Picatinny/Weaver rail, they do not come with this adaptor but the adaptor is available below if you need one.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Konos 15cm to 22cm Bipod with notched legs (6" to 9" approx)

The Konus 15cm to 22cm bipod is a well made copy of the Harris bipod and uses superior materials that give the bipod extra rigidity over may of the other copies out there. If you look at this bipod and put a Harris alongside it you would be hard pressed to see the difference except in the price. The built-in swivel rotates to either side for instant levelling on uneven ground. The hinge base with tension adjustment and buffer springs. This bipod has notched legs to allow for easy one handed adjustment of the height  A branded product for the same money as some shops sell unbranded copies of dubious quality.  This Bipod uses the standard sling swivel for attachment to a firearm in the same way a Harris bipod does 45.00

Konos 22cm to 33cm Bipod with notched legs (9" to 13" approx) 45.00

The Konus 22cm to 33cm bipod is a well made copy of the Harris bipod and uses superior materials that give the bipod extra rigidity over may of the other copies out there. If you look at this bipod and put a harries alongside it you would be hard pressed to see the difference except in the price.The built-in swivel rotates to either side for instant levelling on uneven ground. The hinge base with tension adjustment and buffer springs. This bipod has notched legs to allow for easy one handed adjustment of the height  A branded product for the same money as some shops sell unbranded copies of dubious quality. This Bipod uses the standard sling swivel for attachment to a firearm in the same way a Harris bipod does  45.00

 

AirForce1 Pro-Tilt 9"-15" Bipod

The AirForce1 Pro-Tilt Bipods are not quite the same quality as the Konus bipod but is good value for the money,  they are manufactured with the heat treated steels, and hard alloys. The built-in swivel rotates to either side for instant levelling on uneven ground. The hinge base with tension adjustment and buffer springs. The Bipod attaches to a standard Sling Swivel Stud.  This bipod has notched legs to allow for easy one handed adjustment of the height

This Bipod uses the standard sling swivel for attachment to a firearm in the same way a Harris bipod does. 35.00

 

AirForce1 Pro-Tilt 13"-22" Bipod

This bipod looks  the same as the bipod pictured above except it has longer legs.The AirForce1 Pro-Tilt Bipods are manufactured with the  heat treated steels, and hard alloys. The built-in swivel rotates to either side for instant levelling on uneven ground. The hinge base with tension adjustment and buffer springs. This bipod has notched legs to allow for easy one handed adjustment of the height

This Bipod uses the standard sling swivel for attachment to a firearm in the same way a Harris bipod does. 40.00

 

Bipod Tightening Handle for Airforce  and Konos

The Bipod tightening handle fits in place of the knurled adjustment nut on the above bipods and allows easy adjustment of the swivel head. it is now possible to adjust the rock of the head from very loose to no movement with one hand on the firing point. By pressing the orange button the handle can slide around the central shaft without turning it thus allowing the handle to be moved to the best position for easy adjustment. Only fits bipods with a 5mm mail thread such as the ones listed above. 5.00

No fitting charge if purchased at the same time as one of the above bipods

 

 

 

Atlas Type Bipod

This Rifle Bipod   fits a  Picatinny Rail and is quick detachable via a lever release system.

It is adjustable from 6.5 - 9 inch

SpecificationsColor: Black
Weight: 13oz. / 362g
Adjustable Leg Lengths: 6.5-9 inch
Material: Aluminum Fits 20mm Rail QD Mount Features Full Pan & Tilt  40.00

 

 

 

 

 

 

Firewolf Bipod

Fully adjustable Pan and Tilting Head, Adjustable Leg Lengths: 7.25 - 9 inches, Weight 11.29oz, Attaches to a 1913 Picatinny rail and mounts in seconds

Legs can be placed in one of 5 positions front to back and can be  extended through 4 positions

Colour: Black, Material: Aluminium

Legs are spring-loaded and retract with the touch of a button.

The leg extension design allows the shooter to quickly adjust to different heights without having to align each leg equally. 40.00

 

 

 

 

 

 

 

Firewolf Long range bipod

 

This long leg Long Range Accuracy Light Tactical Bipod adjusts from 6.6"" to 10"" with a 10 left and right adjustable cant and legs positions including 0, 22, 45, and 90.

Specifications Weight: 1.4 lbs 80.00

 

 

 

 

Lightweight Telescopic shooting sticks (Tripod)

HSF Shooting Stick Lightweight versatile telescopic shooting sticks designed to provide a steady rest out in the field. Adjustable between 33" and 75" 30.00

 

 

 

 

 

 

 

 

Lightweight Telescopic shooting sticks (Bipod)

 

HSF Shooting Stick Lightweight versatile telescopic shooting sticks designed to provide a steady rest out in the field. Adjustable between 33" and 75" 25.00

 

 

 

 

 

 

Picatinny rail sling swivel.

This adaptor allows any device that attaches to a standard sling swivel to be attached to a firearm that has a Picatinny/Weaver rail. Commonly use to attach Harris Type Bipods and Slings. 5.00

 

 

 

 

 

 

 

Uncle Mike's Sling Swivel Stud 3/4" Wood Screw 2.00

 

 

 

 

 

Uncle Mike's Sling Swivel Stud 7/8" Machine Screw with Nut  2.00

 

 

 

 

 

 

Second Hand Items:

 

Harris Adaptor no 4 Clamps on to the barrel of your rifle and provides a sling swivel that allows you to attach a bipod or sling. As new 18.00